Galaxy S2 GT-I9100G 4.1.2 JB I9100GXXLSR DBT/ATO Germany & Austria

Samsung has now added another Android 4.1.2 Jelly Bean update  for Samsung Galaxy S2 GT-I9100G.  This time it’s now heading for Germany and Austria owners of  Galaxy S2 GT-I9100G. The firmware build number is still I9100GXXLSR, the same version of  and likely similar to the initial released in France last month.  Again, for those advance users who wants to give it try , since this Android 4.1.2 jelly bean update has becoming to slow before it reaches in your area, you can grab the original stock I9100GXXLSR either DBT for Germany or ATO  for Austria.

I9100GXXLSR

Disclaimer: This guide is for advance users only, if this your first time heard about this method, make a careful research first before proceeding. We shall not be held responsible if anything happens to your device by using this guide. Proceed at your own risk!

How to manually upgrade or install the I9100GXXLSR Android 4.1.2 Jelly Bean on Samsung Galaxy S2 GT-I9100G

Note: This stock firmware is compatible for all Asia and Europe unbranded orunlocked Samsung Galaxy S II with the specification model number  “GT-I9100G″ versions only. The Samsung Galaxy S II GT-I9100G  is visually identical to the GT-I9100 but it is based with an  OMAP4430 SoC instead of the Exynos 4210 processors in the GT-I9100. So, firmware builds are incompatible with each other.

Step 1: Grab the relevant files for flashing I9100XWLS8
– Odin3_v3.07 Flasher tool Odin3_v3.07 link
– Samsung Galaxy S2 USB driverDownload link
– Original I9100GXXLSR Stock ROM

Austria –  download
Germany –  download
France –  download

Step 2: Prepare things  as follows:
– Use a PC or laptop that runs in Windows OS, with a good and perfectly working USBserial port.
– Use the USB cable wire for your Galaxy S2.
– Make sure that your galaxy S2 battery is fully charge.
– Back up all important files stored from your phone’s internal memory – contacts, messages, etc.
– Remember or back up the APN settings of your device.
– Enable USB debugging from your phone’s settings. Go to Settings > Applications > Development, and tick the box that says ‘Enable USB Debugging’.

Step 3: Extract or unzip the downloaded stock firmware so that you’ll get the Odin flashable .tar.md5 file. Use Winzip, winrar, 7zip or any extracting tool you had in your computer.
Step 4: Run and Configure Odin
Run Odin downloader on your PC desktop. Watch out the check-boxes options on the right top of Odin, ensure that the ‘RE-PARTITION’ is unchecked. Leave the ‘AUTO-REBOOT and ‘F.RESET TIME’  remains checked.
Now, click on the PDA button, then select and load the tar file that you have previously extracted.“I9100GXXLSR_I9100GXXLSP_I9100GXEFLSR_HOME.tar.md5″ 

Step 5: Reboot the Galaxy S2 into Download Mode.
To put your galaxy S2 in download mode, just simply switch it off then gently press and hold the “POWER, VOLUME DOWN and HOME” buttons simultaneously. You’ll be then prompted in a warning screen to continue or cancel.

Samsung Galaxy S2 Download Mode button combination

Step 6: Connect the Phone to the Computer or Laptop
Once the phone screen shows in downloading mode, connect your phone to the PC with the USB cable. You’ll then notice the upper box in Odin that turns in yellow color., it also indicates the COM:ID where the device is being detected and a word “added!!’ on the log box. If somehow those things never showed up, check out the USB cable connection, read again from the top of this post.
Step 7: Flash it!
Once all set and ready, hit he “START” button to begin flashing.
Do not touch anything that might interrupt the process to avoid any fatal errors or failures, it may ruin your device if any interruption occurs while already in flashing status.

It may only takes about 3 to 5 minutes, depends of your PC/laptop speeds. A word “PASS” will display in Odin once it finishes. If somehow you will not get the word “PASS” or just stuck in along time. Disconnect the phone, remove battery, re-insert it, check the USB connection, re-install the driver, disable Kies and any anti-virus. Set the phone in Download mode again, and repeat the whole procedure.

The phone will just automatically reboots if the firmware flashing successfully completes. Just wait until it boots up on the “S” logo for a while then into an android update screen. If it still shows boot logo try rebooting and if it stays there, you need to wipe your phone.

Fixing possible issues after flashing like bootloops or just stuck in welcome screen logo

Boot in recovery mode – Press and hold Volume Up, Home and Power button. Use volume keys to select up and down and power or home key to select the option.

1. Select Wipe Data/Factory Reset
2. Next select the Wipe Cache Partition
3. Lastly select Reboot System Now to reboot your Galaxy S2 in Normal mode.
Confirm your fresh firmware installed by typing *#1234# or
Go to Settings>About Phone>Firmware info.
Check and reconfigure your APN settings when data networks connection issues encountered.

Change the default text to your own or desired language

The default language of this firmware French since this a default build for France users only, but it has all major languages around the world included. You can just simply change it from your device text settings.

If you have something to add about this firmware like some exciting features even bugs, issues and etc. Just don’t hesitate to drop it on our comment form below.