Stock N9005XXUGBOI3 Official 5.0 Update on Galaxy Note 3 SM-N9005

Another 5.0 update have landed on the Galaxy Note 3 SM-N9005 to which will bump its build N9005XXUGBOI3. Fortunately, the N9005XXUGBOI3 is only released in Italy and Switzerland at this time being. While looking at N9005XXUGBOI3 build, it looks promising, although the kernel version has remained untouched, but it has an updated baseband version to N9005XXUGBOI2. Noting that there were numerous Android 5.0 update that have been rolled out on the Galaxy Note 3 since its first release way back in February. But nonetheless it was all the same and only brings some minor significant changes.

So those who may want to try it out, you may grab the stock N9005XXUGBOI3 5.0 update itself and manually flash it into your device.

Build details of N9005XXUGBOI3:

N9005XXUGBOI3 Note3 Device: Galaxy Note 3
Model number: SM-N9005
Android version: 5.0 (Lollipop OS)
Baseband version: N9005XXUGBOI2
Kernel version: 3.4.0-4540543
Build number: LRX21V.N9005XXUGBOI3
AP: N9005XXUGBOI3
CP: N9005XXUGBOI2
CSC: N9005ITVGBOG1
Build date: 10 September 2015

Download: N9005XXUGBOI3 5.0 Stock Firmware

The N9005XXUGBOI3 is held available and can be seen via Over-The-Air (OTA) update and by using Kies, if you’re from those mentioned countries. The stock firmware N9005XXUGBOI3 are only for advanced users and are useful for those who might have had a rooted and modified Samsung Galaxy Note 3 SM-N9005 and might have missed this update. You can use the manual method instead if the device will no longer receive any official update via Kies or OTA update. So it is much better to manually install it or otherwise you device may stuck in an outdated firmware build.

FAQ’s About Flashing A Stock Firmware

Q: Will this trip KNOX warranty void flag counter to 0×1?
No, this an official and signed firmware from Samsung, so flashing the official firmware will not trip KNOX apps.
Q: My Galaxy Note 3 is rooted, will I lose root?
If your device was rooted you will lose root right after the installation finished as the device OS will then restored back to the official default settings.

Disclaimer: Use of this method is solely at your own risk! Please proceed with precautions, for we will not take any responsibility if anything happens to your device by using this guide.

  • Make sure that your Galaxy Note 3 battery is to be fully recharge.
  • Back your important data. Stock Firmware packages comes in two formats the ‘Full-Wipe’ (delete your stored data after flashing) and the ‘Non-Wipe’ (it doesn’t delete your phone’s stored data) but it is highly recommended to make a back up all important files stored from your phone’s internal memory – contacts, messages, etc. before flashing no-matter if it is Full-Wipe or Non-Wipe, just to be safe and ensure that your stored data are in safe if something went wrong during the flashing process.
  • Use a PC with a good and perfectly working USB serial port. Odin will not work on MAC OS.
  • Use the supplied USB cable for your Galaxy Note 3.
  • Enable USB debugging from your phone’s settings – Go to Settings > About device > then scroll down to the build number and tap that number for around 7-times ’til the Developer option appear. Then hit back in Settings > Developer options then tap the USB debugging check box.
  • TURN OFF the Reactivation Lock if its enabled on your device – juts tap on Settings > Security > Reactivation Lock and then unchecked the Turn Reactivation lock on.
    Ensure that KIES is closed and not running in the system tray! Kies and Odin are both created by Samsung, but Kies will interrupt and doesn’t like Odin, it will block you from flashing.

Note: These stock ROMs are both unbranded and carrier branded stock firmware packages. If you install the unbranded ones it on a branded or carrier locked Galaxy Note 3 (SM-N9005), you’ll lose the default logo and apps of that said network operator. While installing the unbranded ones over a carrier devices it will just de-brand it and you’ll lose some important apps on that particular network provider.

Flasher Tool:
Odin3_v3.09 – Find it here
USB driver – Drivers are here

Install the USB Driver first to get rid of flashing failures. Also, you must unzip or extract the downloaded file which is packed in zip, so that you’ll get the tar.md5 file.

Run and Configure Odin

Run Odin downloader Odin3_v3.09 on your PC desktop. Watch out the check-boxes options on the right top of Odin, ensure that the both ‘AUTO-REBOOT’ and ‘F.RESET TIME’ checkboxes must be checked. Only the ‘RE-PARTITION’ remains unchecked.

Reboot your Galaxy Note 3 into Download Mode

To reboot the Galaxy Note 3 into download mode , you need to turn the power off. After it completely shut off, just press and hold the Volume Down, Home and the Power ON/OFF button simultaneously. You should then prompted into a warning screen and asking you to press volume up if you want to continue or volume down to cancel, just simply press volume up to get into download mode. The download mode then displays an Android robot and say’s “Downloading.. Do not turn off target!!”

Connect your Phone into your computer

Once you already reboot the phone in download mode, simply connect the phone to your PC or laptop USB. In Odin window – the ID:COM box will turn to blue color and indicates the COM port number and a word “Added” on a log box will prompt you that the device is already detected or recognized by Odin. Your COM port number might be different from mine. If you do not see a COM port number then there’s something missing or wrong. You may read again from the top of this post.

Load the N9005XXUGBOI3 5.0 Android Lollipop stock

The stock firmware is pack in a single .tar.md5 file only. Now, you need to just simply click on the AP button, then browse to the folder where the file you have previously extracted and then select and load the firmware file like this. “N9005XXUGBOI3_ N9005ITVGBOG1_N9005XXUGBOI2_HOME.tar.md5″

Start to Flash the BOI3 5.0 binary file

Once if all set and ready to fire-up, hit the “START” button in Odin to begin flashing the stock-ROM.
Do not ever interrupt the phone while already in flashing progress, like disconnecting the cable or turning off the device. Just wait until it completely finishes.

Wait on PASS!!

When the Stock Firmware installation successfully completes, you will then see a word “PASS” in Odin. This indicates that the flashing was already finished, and on the log box it says “All threads completed (succeed 1 / failed 0)”. The phone will just then automatically reboot, then it’s about time to remove it from PC or laptop USB connection.

Confirm if you successfully installed the stock firmware

Confirm your fresh firmware installed. Go to Settings > About Device then look for the baseband version and build number must be on N9005XXUGBOI3.

Possible errors that you may encounter, this is based on my own experience while flashing stock firmware on Samsung Android devices. These are just a few hints on how to resolved it.

Q: I got an error message that says “Set-up connection Failed” ?
A: 1. Check your USB connection from the phone to PC,
2. Connect to another PC USB port
3. Check and or try to another USB cable
4. Re-install the USB driver.
Q: Odin just suddenly stuck in the middle of nowhere while in flashing progress, it isn’t responding at all?
A: Check for possible program that might interrupt the process, like disabling the anti-virus and closing any running programs. Also, try to use another computer or laptop,
Q: I experienced bootloop or the phone just stuck on Welcome Logo (phone always stop at bootanimation) and it won’t boot normally?
A: This will eventually happen if your device came from custom firmware, but you can fix it via recovery mode.
Boot in recovery mode
1. Press and hold Volume Up, Home and Power button.
2. Use volume keys to select, Up and Down and Power or Home key to select the option
3. Select Wipe Data/Factory Reset using the Home button.
4. Next select the Wipe Cache Partition
5. Lastly, select Reboot System Now to reboot your Galaxy Note 3 in Normal mode.

That’s it! Just let us know if you have issues upon flashing the stock N9005XXUGBOI3 5.0 Lollipop.