I9507XXUENB5 4.3 Firmware Galaxy S4 TD-LTE GT-I9507, Manual install

I9507XXUENB5 Android 4.3 firmware for Galaxy S4 TD-LTE GT-I9507.  The I9507XXUENB5 is an update from previous build 4.2.2 I9507XXUENB5.  There are only two variants of Galaxy S4 TD-LTE GT-I9507 we have seen, those are from Hong Kong and Optus Australia. This  I9507XXUENB5 4.3 firmware belongs to Optus Galaxy S4 TD-LTE variants and not for Hong Kong devices.

The Android 4.3  I9507XXUENB5 can now download via over-the-air or OTA update or Kies. But Australian advanced users and developers can now manually grab the I9507XXUENB5 4.3 stock  firmware from below source. I also added some guide on how to manually flash it through Odin flasher tool.  This method has been also useful if your phone has been rooted or modified and did not received this update officially from OTA or Kies.

Android-4.3-Jelly-Bean

How to manually upgrade or install the I9507XXUENB5 Android 4.3 Jelly Bean on Samsung Galaxy S4 TD-LTE GT-I9507

Again, this update is now officially released in Australia, you can simply update your Galaxy S4 by checking through Samsung KIES or OTA. Below are the official I9507XXUENB5 stock firmware for developers and advance users, and can be flash using ODIN if their devices has been rooted and can’t get any official update anymore.

Install procedures:

Disclaimer: This guide is for advance users only, if this your first time heard about this method, make a careful research first before proceeding. We shall not be held responsible if anything happens to your device by using this guide. Proceed at your own risk!

Note: This stock firmware is compatible for Samsung Galaxy S4 TD-LTE with the specification model number  “GT-I9507″ versions only.

Download the stock Android 4.3 I9507XXUENB5 firmware:
Australia (Optus only)  – OPS_I9507XXUENB5 link

Odin3_v3.09 download
Kies 3 USB Driver download

Step 2: Prepare things  as follows:
– Use a PC or laptop that runs in Windows OS, with a good and perfectly working USB serial port.
– Use the USB cable wire for your Galaxy S4.
– Make sure that your Galaxy S4 battery is fully charge.
– Back up all important files stored from your phone’s internal memory – contacts, messages, etc.
– Remember or back up the APN settings of your device.
– Enable USB debugging from your phone’s settings. Go to Settings > Applications > Development, and tick the box that says ‘Enable USB Debugging’.
– Do a “Hard Reset” if you have a lot of 3rd party applications installed from your phone, this is useful to gain a smooth flashing. (Just make sure that you already back up all your important files before resetting your device.

Step 3: Extract or unzip the downloaded stock firmware so that you’ll get the Odin flashable .tar.md5 file. Use Winzip, winrar, 7zip or any extracting tool you had in your computer.

Step 4: Run and Configure Odin
Run Odin downloader on your computer’s desktop. Watch out the check-boxes options on the right top of Odin, ensure that the ‘RE-PARTITION’ is unchecked. Leave the ‘AUTO-REBOOT and ‘F.RESET TIME’  remains checked.
Now, click on the AP button, then select and load the tar file that you have previously extracted.  “I9507XXUENB5_HOME.tar.md5″

Odin sample only:
Android 4.3 Samsung Galaxy S4 GT-I9505 Install Odin
Step 5: Reboot the Galaxy S4 I9505 into Download Mode.
To put your Galaxy S4 I9507 in download mode, just simply switch it off then gently press and hold the “POWER, VOLUME DOWN and HOME” buttons simultaneously. You’ll be then prompted in a warning screen to continue or cancel.

Step 6: Connect the Phone to the Computer or Laptop
Once the phone screen shows in downloading mode, connect your phone to the PC with the USB cable. You’ll then notice the upper box in Odin that turns in yellow color., it also indicates the COM:ID where the device is being detected and a word “added!!’ on the log box. If somehow those things never showed up, check out the USB cable connection, read again from the top of this post.
Step 7: Flash it!
Once all set and ready, hit he “START” button to begin flashing.
Do not touch anything that might interrupt the process to avoid any fatal errors or failures, it may ruin your device if any interruption occurs while already in flashing status.

It may takes a couple of minutes or longer and it depends of your PC/laptop speeds. A word “PASS” will display in Odin once it finishes. If somehow you will not get the word “PASS” or just stuck in along time. Disconnect the phone, remove battery, re-insert it, check the USB connection, re-install the driver, disable Kies and any anti-virus. Set the phone in Download mode again, and repeat the whole procedure.

The phone will just automatically reboots if the firmware flashing successfully completes. Just wait until it boots up on the “Samsung” logo for a while then into an android update screen. If it still shows boot logo try rebooting and if it stays there, you need to wipe your phone.

Fixing possible issues after flashing like bootloops or just stuck in welcome screen logo

Boot in recovery mode – Press and hold Volume Up, Home and Power button. Use volume keys to select up and down and power or home key to select the option.

1. Select Wipe Data/Factory Reset
2. Next select the Wipe Cache Partition
3. Lastly select Reboot System Now to reboot your Galaxy S4 in Normal mode.
Confirm your fresh firmware installed by typing *#1234# or
Go to Settings>About Phone>Firmware info.
Check and reconfigure your APN settings when data networks connection issues encountered.

Change the default text to your own or desired language

The default language of this firmware varies according to which country specific software build you have installed, but it has all major languages around the world included. You can just simply change it from your device text settings.

You may then confirm the newly installed 4.3 Jelly Bean from your device:
Go to Settings>>About Device>> Firmware info or type *#1234# and see if it’s already got the baseband  I9507XXUENB5 and a Android 4.3 version.  That’s it! If this helps you then simply share us some love by hitting our like and share buttons. If you also have something to add, your comments and suggestions are most welcome here.

Comments are closed.