The long-awaited official Android 4.1.2 Jelly Bean update on Samsung Galaxy S2 GT-I9100 is currently hitting in Spain, other countries might also follow soon. But for those advance users who couldn’t wait much longer and wants to upgrade their devices right now can manually install the original I9100XWLS8 stock ROM. This method has been also useful for those devices that is now rooted or installed with custom firmware and wants to restore back to Samsung’s official firmware. Just follow this simple steps and your device will get updated to official Android 4.1.2 Jelly Bean in no time.
Disclaimer: This guide is for advance users only, if this your first time heard about this method, make a careful research first before proceeding. We shall not be held responsible if anything happens to your device by using this guide. Proceed at your own risk!
How to manually upgrade or install the I9100XWLS8 Android 4.1.2 Jelly Bean on Samsung Galaxy S2
Note: This stock firmware is compatible for all Europe unbranded or unlocked Samsung Galaxy S II with the specification model number “GT-I9100” versions only.
Updates: Added some unbranded Original 4.1.2 Stock ROM
Spain – FOP I9100XWLS8
Spain – FOP I9100XWLSD
Italy – ITV I9100XWLSD
Germany – DBT I9100XWLSD
Nordic Cuuntries – NEE I9100XWLSD
Nordic Countries – NEE I9100XWLSJ
The Netherlands – XEN I9100XWLSD
Baltic States – SEB I9100XWLSD
Russia – SER I9100XWLSE
Saudi Arabia – KSA I9100XWLSD
Australia – XSA I9100XWLSH
Stock Firmware Downloads: Samsung Galaxy S2 GT-I9100 Firmware
Step 2: Prepare things as follows:
– Use a PC or laptop that runs in Windows OS, with a good and perfectly working USB serial port.
– Use the USB cable wire for your Galaxy S2.
– Make sure that your galaxy S2 battery is fully charge.
– Back up all important files stored from your phone’s internal memory – contacts, messages, etc.
– Remember or back up the APN settings of your device.
– Enable USB debugging from your phone’s settings. Go to Settings > Applications > Development, and tick the box that says ‘Enable USB Debugging’.
– Do a “Hard Reset” if you have a lot of 3rd party applications installed from your phone, this is useful to gain a smooth flashing. (Just make sure that you already back up all your important files before resetting your device.
Step 3: Extract or unzip the downloaded stock firmware so that you’ll get the Odin flashable .tar.md5 file. Use Winzip, winrar, 7zip or any extracting tool you had in your computer.
Step 4: Run and Configure Odin
Run Odin downloader on your PC desktop. Watch out the check-boxes options on the right top of Odin, ensure that the ‘RE-PARTITION’ is unchecked. Leave the ‘AUTO-REBOOT and ‘F.RESET TIME’ remains checked.
Now, click on the PDA button, then select and load the “I9100XWLS8_I9100XXLS8_I9100FOPLS3_HOME.tar.md5″ that you have previously extracted.
Step 5: Reboot the Galaxy S2 into Download Mode.
To put your galaxy S2 in download mode, just simply switch it off then gently press and hold the “POWER, VOLUME DOWN and HOME” buttons simultaneously. You’ll be then prompted in a warning screen to continue or cancel.
Step 6: Connect the Phone to the Computer or Laptop
Once the phone screen shows in downloading mode, connect your phone to the PC with the USB cable. You’ll then notice the upper box in Odin that turns in yellow color., it also indicates the COM:ID where the device is being detected and a word “added!!’ on the log box. If somehow those things never showed up, check out the USB cable connection, read again from the top of this post.
Step 7: Flash it!
Once all set and ready, hit he “START” button to begin flashing.
Do not touch anything that might interrupt the process to avoid any fatal errors or failures, it may ruin your device if any interruption occurs while already in flashing status.
It may only takes about 3 to 5 minutes, depends of your PC/laptop speeds. A word “PASS” will display in Odin once it finishes. If somehow you will not get the word “PASS” or just stuck in along time. Disconnect the phone, remove battery, re-insert it, check the USB connection, re-install the driver, disable Kies and any anti-virus. Set the phone in Download mode again, and repeat the whole procedure.
The phone will just automatically reboots if the firmware flashing successfully completes. Just wait until it boots up on the “S” logo for a while then into an android update screen. If it still shows boot logo try rebooting and if it stays there, you need to wipe your phone.
Fixing possible issues after flashing like bootloops or just stuck in welcome screen logo
Boot in recovery mode – Press and hold Volume Up, Home and Power button. Use volume keys to select up and down and power or home key to select the option.
1. Select Wipe Data/Factory Reset
2. Next select the Wipe Cache Partition
3. Lastly select Reboot System Now to reboot your Galaxy S2 in Normal mode.
Confirm your fresh firmware installed by typing *#1234# or
Go to Settings>About Phone>Firmware info.
Check and reconfigure your APN settings when data networks connection issues encountered.
Change the default text to your own or desired language
The default language of this firmware is Spanish – (Spanol), for this is Spain specific software build, but it has all major languages around the world included. You can just simply change it from your device text settings.
All Included languages:
- Deutsch (Deutschland)
- Deutsch (Osterreich)
- Deutsch (Schweiz)
- English (Australia)
- English (New Zealand)
- English (United Kingdom)
- English (United States)
- Espanol (Spania)
- Espanol (Estados Unidos)
- Francais (Belgique)
- Francais (France)
- Nederlands (Belgie)
- Nederlands (Nederland)
- Norsk bokmal
- Portugues (Brasil)
- Portugues (Portugal)
- others which I can’t read
That’s it! If this helps you then simply share us some love by hitting our like and share buttons. If you also have something to add, your comments and suggestions are most welcome here.