Middle East Samsung Galaxy S2 users, here it comes your Samsung Galaxy S2 GT-I9100 official Android 4.1.2 Jelly Bean firmware update. The official Arabic firmware build has began rolling out in United Arab Emirates and Iraq, other Middle East regions will get this update as well very soon. The firmware build number is I9100XWLSD, the same build number and baseband version –I9100XXLS8 as released in Europe regions earlier but this time it has a default Middle East regions CSC codes I9100OJVLS6.
Firmware Update: I9100XWSLD_I9100OJVLS6 4.1.2 Jelly Bean
Region: Middle East
Device: Samsung Galaxy S II GT-I9100
Release: February 2013
This update is now available via Samsung Kies. So, if you came from Middle East countries, just check it out on Kies. Those who came from other parts of the world and wanted to install Arabic firmware on Samsung Galaxy S2, you can grab the stock ROM and manually install it using Odin.
How to manually upgrade or install the I9100XWLSD Arabic Firmware Android 4.1.2 Jelly Bean on Samsung Galaxy S2
Disclaimer: This guide is for advance users only, if this your first time heard about this method, make a careful research first before proceeding. We shall not be held responsible if anything happens to your device by using this guide. Proceed at your own risk!
Step 1: Grab the relevant files for flashing I9100XWLS8
– Odin3_v3.07 Flasher tool Odin3_v3.07
– Samsung Galaxy S2 USB driver, Download
– Original I9100XWLSD Stock ROM
Note: This stock firmware is compatible for all Europe unbranded or unlocked Samsung Galaxy S II with the specification model number “GT-I9100″ versions only.
United Arab Emirates – I9100XWLSD_I9100OJVLS6_XSG.zip
Stock Firmware Downloads: Samsung Galaxy S2 GT-I9100 Firmware
Step 2: Prepare things as follows:
– Use a PC or laptop that runs in Windows OS, with a good and perfectly working USB serial port.
– Use the USB cable wire for your Galaxy S2.
– Make sure that your galaxy S2 battery is fully charge.
– Back up all important files stored from your phone’s internal memory – contacts, messages, etc.
– Remember or back up the APN settings of your device.
– Enable USB debugging from your phone’s settings. Go to Settings > Applications > Development, and tick the box that says ‘Enable USB Debugging’.
– Do a “Hard Reset” if you have a lot of 3rd party applications installed from your phone, this is useful to gain a smooth flashing. (Just make sure that you already back up all your important files before resetting your device.
Step 3: Extract or unzip the downloaded stock firmware so that you’ll get the Odin flashable .tar.md5 file. Use Winzip, winrar, 7zip or any extracting tool you had in your computer.
Step 4: Run and Configure Odin
Run Odin downloader on your computer’s desktop. Watch out the check-boxes options on the right top of Odin, ensure that the ‘RE-PARTITION’ is unchecked. Leave the ‘AUTO-REBOOT and ‘F.RESET TIME’ remains checked.
Now, click on the PDA button, then select and load the tar file that you have previously extracted. For example I’m using the Italian firmware so I got the “I9100XWLSD_I9100OJVLS6_I9100XXLS8_HOME.tar.md5″
Step 5: Reboot the Galaxy S2 into Download Mode.
To put your galaxy S2 in download mode, just simply switch it off then gently press and hold the “POWER, VOLUME DOWN and HOME” buttons simultaneously. You’ll be then prompted in a warning screen to continue or cancel.
Step 6: Connect the Phone to the Computer or Laptop
Once the phone screen shows in downloading mode, connect your phone to the PC with the USB cable. You’ll then notice the upper box in Odin that turns in yellow color., it also indicates the COM:ID where the device is being detected and a word “added!!’ on the log box. If somehow those things never showed up, check out the USB cable connection, read again from the top of this post.
Step 7: Flash it!
Once all set and ready, hit he “START” button to begin flashing.
Do not touch anything that might interrupt the process to avoid any fatal errors or failures, it may ruin your device if any interruption occurs while already in flashing status.
It may only takes about 3 to 5 minutes, depends of your PC/laptop speeds. A word “PASS” will display in Odin once it finishes. If somehow you will not get the word “PASS” or just stuck in along time. Disconnect the phone, remove battery, re-insert it, check the USB connection, re-install the driver, disable Kies and any anti-virus. Set the phone in Download mode again, and repeat the whole procedure.
The phone will just automatically reboots if the firmware flashing successfully completes. Just wait until it boots up on the “S” logo for a while then into an android update screen. If it still shows boot logo try rebooting and if it stays there, you need to wipe your phone.
Fixing possible issues after flashing like bootloops or just stuck in welcome screen logo
Boot in recovery mode – Press and hold Volume Up, Home and Power button. Use volume keys to select up and down and power or home key to select the option.
1. Select Wipe Data/Factory Reset
2. Next select the Wipe Cache Partition
3. Lastly select Reboot System Now to reboot your Galaxy S2 in Normal mode.
Confirm your fresh firmware installed by typing *#1234# or
Go to Settings>About Phone>Firmware info.
Check and reconfigure your APN settings when data networks connection issues encountered.